Getting Familiar with Plumbing: A Must for Installing a Bathtub

Click Here

We have come across this great article involving Installing A Bathtub below on the net and felt it made sense to relate it with you on this page.


Tools You Need to Install a New Bathtub
Setting up a bathtub isn't precisely rocket science, yet it does need solid plumbing, woodworking, and often, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably hard job. If the old bathtub is easily easily accessible, the job can relocate easily; if you need to open a wall surface to eliminate the old tub as well as position the brand-new bathtub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub as well as embeded in the new one. Make certain you have actually qualified yourself for the task and also fit attempting it. Instead of employing a professional to take over a halfway-completed job, it is far better to consider employing one prior to you start. Opportunities are you may require an expert plumber to make tube links.
This write-up will certainly aid you mount a new bathtub in your washroom if you have actually currently acquired a brand-new bathtub as well as don't need to change the setup of your previous water pipelines.
Your tools and product checklist should consist of the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome as a result of the limited access that is usually the case.
    Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a towel all set for the remaining water that will come from the pipes. When the supply pipes have actually been removed, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from transforming throughout this process. Once the taps have actually been removed, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
    Prior to carrying on to fit the brand-new taps, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.

    Fitting New Touches


    If the tails of the brand-new taps are plastic, after that you will need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipes.
    If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
    Next off, position the faucet in the placing hole in the bath/basin making certain that the washers remain in location between the faucet and also the sink. Secure the tap in place with the maker supplied backnut. When the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap adapters. The previous kind should be attached to the faucet ends initially, tightening just by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Setting up the Bathtub


    Using both wood boards under its feet, put the bathtub in the called for setting. The wooden boards are useful in equally spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 small factors.
    The next goal is to guarantee that the tub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the bath tub up until the level reviews level.
    To set up taps, fit the bottom of the outermost versatile tap connector to the proper supply pipeline by making a compression sign up with; after that do the very same for the other tap.
    Turn on the water supply and check all joints and also new pipework for leaks and also tighten them if required. Fill the bathtub as well as additionally examine the overflow outlet and the typical electrical outlet for leakages.
    Finally, take care of the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bath tub ought to wait up until the bathtub has been used a minimum of once as this will certainly settle it right into its final setting.

    Preparing for the Setup


    First of all, the sustaining framework provided with the bath should be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the tap features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps unit to avoid stress on the bathtub.
    Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
    Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now prepare to be fitted in its final placement.

    Tiling Around the Bathtub


    In the location where the bath satisfies the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to fracture an inflexible seal, causing the water to pass through the wall surface between the bathroom and also the tiling, bring about difficulties with moisture and also feasible leaks to the ceiling listed below.
    You can choose from a range of coloured sealants to blend in your fixtures and also fittings. They are offered in tubes as well as cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to allow for the movement experienced when the tub is in usage. The sealer can fracture rather very early if you do not consider this movement before sealing.
    Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly readily available on the marketplace. It is a good idea to fit the floor tiles using water-resistant or water resistant glue and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Installing A Bathtub

    I am just very serious about Tools You Need to Install a New Bathtub and I am assuming you enjoyed reading the entire blog entry. So long as you appreciated our blog posting kindly don't forget to share it. I take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


    Solve it now, dial here!

    Leave a Reply

    Your email address will not be published. Required fields are marked *